Tables Have Turned (Almost!)

I don’t have many photos to show for it, but I spent five or six hours yesterday mounting the motor and truing up the alignment. I mostly figured it out, but it wasn’t as simple to install as I expected!

I also mounted the Arduino/motor shield/DCC shield tower and wired it up. There’s no power yet, but that should be coming soon! I left plenty of space to reach my hand between the motor and the tower. One of the most frustrating issues with LSR’s first iteration was that some under-the-table components were too close together, making it difficult and uncomfortable to make adjustments.

Additionally, I am altering the track plan a bit to make better use of the left-hand side of the module. In the following track plan you can see that I’ve pushed the goods shed access track further back. This opened up a larger yard around the station platform and adds a bit of “flow” and balance to the overall design.

LSR and extension

 

Turntable Well

Well that was less than easy. I realized too late that the circumference of the hole was too small, so I had to freehand it. As a result, I over-carved the hole and had to go back and fill it in with Dap Plastic Wood. This extended the project by a couple of days, but the well is now fitted. Not as slick as it could have been, but still pretty slick!

More of the Same, Part II

Spent a few minutes roughing out the track. Kato is insanely easy to work with. Runaround is long enough for two-car passenger operations, which is exactly what I was hoping for, as I will be mostly running mixed trains. They will be split upon arrival, with the 0-6-0 Bellwether handling the goods while the 2-8-0 (which will be christened soon) runs around, pushes the coach to the platform, and then turns around on the turntable before topping off with water and coal for the return trip.

Then I started on the recess for the turntable, using a hole-cutting attachment on a Dremel. I will have to “scrape” the recess out using another Dremel attachment. I started before realizing how much dust it makes. This will be an outside job.

More of the Same, and Some New Toys

Continuing the LSR rebuild, I was wondering how to “end” the rails leading to the second module in such a way that they could simply butt up against the corresponding rails without worrying about fishplate connectors, extension track, etc.

While I was sanding splinters from the new module this evening, it dawned on me that I could cut the roadbed out from under the ends of the rails, and then have the rail-ends jut out over the fascia (which I already plan on doing for track leading onto the turntable).

Here is the underside of a short piece of test track, after I cut the roadbed back with a razor saw:

And here’s how the rails might look jutting out over the fascia, after a few hills have been carved at the corners:

I think this is a good solution. It might look a bit odd, as there will be about an inch of rail without ties, but once it is all painted it shouldn’t be too obvious.

In addition to adding that one short fascia, I put some adjustable feet on the bottom of the module, 1′ from each corner:

Most importantly, I received this today: a DCC-equipped Dapol 38XX Class 2-8-0 steam engine, and a couple of 3rd class Collett coaches. Good incentive to keep moving along with this project!

A funny side note:

These would have arrived yesterday, but the postman who was delivering the parcel read the contents list and saw that it contained chocolate and cream. He didn’t want to leave it on the warm porch, so he left a note and asked if I would rather pick it up at the post office. I called and let him know that “chocolate and cream” is the livery scheme on the passenger cars. I don’t think he understood, but he said he’d deliver the parcel anyway, as long I wouldn’t hold him accountable for any spoilage.

And Now For Something Completely Different… But Almost the Same

It has been a while since I’ve posted anything, and here’s why: I made several “mechanical” decisions long ago that are now compromising the operational integrity of LSR.

I had been spending too much time fiddling with the Tortoise (SMAIL) under-table turnout switches because they weren’t working consistently. The remote Tortoise mounting system was complicated and required constant adjustments, and the SPDT switches weren’t powering the frogs reliably. As a result, my engine often got hung up on turnouts and I could only get it going again by turning the power off and then on again. Over time, these turnout issues would only get worse. In retrospect, I should have simply used solenoid switch machines from the start.

Also, the stepper motor that drives LSR’s turntable continually fell out of alignment and caused the deck to lean. This was probably due to the slight warping of my poorly planned mounting block. Unfortunately, I couldn’t simply re-mount the motor due to the spatial needs of track wiring. Had I planned to mount the motor separately from the turntable I would have wired the entire layout differently (you may recall that my initial plan was to use Peco’s long-promised but never-delivered DCC turntable motor, which would have mounted directly to the underside of the turntable).

So, for the past couple of months, rather than flipping the module over every time I wanted to run my engine, I decided to spend my time assessing these issues. If you know me at all, you’ll know what that means. I don’t accept change right away and I sit with new ideas for a good long time before acting on them. After much deliberation I’ve finally come to the conclusion that I need to replace all of my turnouts, which means that I also need to replace the rest of my track. In turn, this means that I also need to replace the baseboard. Essentially, I am starting over, but I intend for this rebuild to move along very quickly.

I’ve purchased nearly all of the necessary materials already. I will be using Kato Unitrack, which snaps together easily and makes the grueling act of soldering feeders obsolete. I’ve used Unitrack in the past, and  having now experienced Peco  I prefer the reliability of Kato’s turnouts despite the snappy action of solenoid switches. The most difficult part will be making Kato turnouts DCC-friendly. For that, I will rely on six NMC Switch-Kat decoders. I sold my Tortoise (SMAIL) machines on eBay and purchased the Switch-Kats with the proceeds.

The only drawback of using Unitrack is that it isn’t just rails mounted across ties   the ties are built into a rigid roadbed which is molded to look like ballast. This is what makes Kato so reliable and easy to install, and for a mainline it looks pretty good out of the box. For stations and yards, though, there’s the cosmetic problem of roadbed height. In a real railway station you won’t usually find the tracks sitting high up on a layer of ballast; rather, the ties will be level (or nearly level) with the ground. To counteract Unitrack’s roadbed height, I will use 3/16″ foam core board to raise the surrounding terrain. I will then fill the gaps between the foam and track with Woodland Scenics’ Foam Putty.

In the idle hours a couple of weeks ago, I also decided to redesign the layout a bit to cut some wasted space and add operational interest. Here is the track plan that I’ve come up with, along with a proposed extension:

LSR and extension

This module will be 12″ x 66,” so is 4″ thinner than its predecessor. You will also notice that I removed the siding in front of the station and added a siding behind it for the cattle dock and (more importantly) goods shunting.

As for the turntable: I am reusing the Arduino, motor shield, and DCC shield, but I am changing the mounting system for the motor. This time, instead of using a 14″ length of dimensional lumber with a hole drilled into it, I have 3-D printed a mount to keep the motor flush with the well of the turntable:

Nema Mount

This is designed to fit my Nema 17 motor, and it will be attached directly to the underside of the baseboard. The hole that I cut for the turntable will only be recessed halfway through the baseboard above it, except for a “through” hole for the shaft and another for the feeder wires.

Additionally, I used TinkerCAD to design a 3-D printed turntable “mounting ring” that specifically fits the Peco turntable and lifts it 1.59mm   just enough to reach the bottom of Kato’s rails. I considered using cardboard or balsa wood for this, but I was afraid that it would warp and cause alignment issues later on.

Peco Turntable Riser for Kato Unitrack

Now it’s time to get building!

I picked up a slab of 3/4″ birch plywood and asked the clerk at the shop to make a few rough cuts. Rather than purchasing dimensional lumber for the frame, I simply asked if he could rip some 3″ strips from the excess ply. The cuts aren’t perfect, but with some sanding they will suit their purpose.

image4-e1558404087561.jpeg

I cut a rectangular notch from of one of the 3″ boards to fit the plug for the DCC throttle. Then, I used wood glue to tack the longer sides to the baseboard. After that, I cut a couple of shorter sides of 3″ board and glued them to each end. Finally, I countersunk some 1½” construction screws every ~6″ around the perimeter. Pretty simple, and the whole operation took an hour.

image1

image3.jpeg

Here you can see it in place, with the motor mount and the turntable ring ready for service:

Tomorrow, I will sand down some edges and then add fascia, feet, etc. In 3-4 days I should already be wiring and laying track. Stay tuned!